Convert inch-pounds (in·lb) to newton-meters (N·m) and vice versa. Includes foot-pounds, kgf·cm, oz·in outputs, common torque specs table, and conversion factor reference.
This converter turns inch-pounds into newton-meters for torque specs that move between imperial manuals and metric tools. It is the right unit change when you are reading a service manual in in·lb but tightening with an N·m wrench.
The page also shows the related torque units people usually need next, including foot-pounds, kilogram-force centimeters, kilogram-force meters, and ounce-inches. The magnitude bar and reference table are there to make low and medium torque values easier to sanity-check.
Use it for fastener specs in automotive, bicycle, electronics, and small-engine work where a small unit mistake can matter. It is most helpful when the spec is low enough that confusing inch-pounds with foot-pounds or newton-meters would create a very large over-torque error on a small fastener. It also helps when the manual, the torque wrench, and the inspection sheet are all using different but related torque units in the same job on one assembly.
Torque conversions are often needed at the point of use, not after the fact. This page keeps the inch-pound and newton-meter values side by side and includes nearby torque units so you can verify the number before tightening anything. That makes it easier to move between mixed-unit tools, manuals, and fastener specs without relying on memory.
Inch-pounds to Newton-meters: N·m = in·lb × 0.112985 Newton-meters to Inch-pounds: in·lb = N·m × 8.85075 Inch-pounds to Foot-pounds: ft·lb = in·lb / 12 Newton-meters to kgf·cm: kgf·cm = N·m × 10.1972 Inch-pounds to Ounce-inches: oz·in = in·lb × 16
Result: 11.299 N·m
100 inch-pounds × 0.112985 = 11.299 N·m. This is also 8.333 foot-pounds. That torque level is typical for small automotive bolts like valve cover fasteners.
Torque is a rotational force measured as force × distance. In the imperial system, this is pound-force × distance in feet or inches, giving foot-pounds (ft·lb) or inch-pounds (in·lb). The SI unit is the newton-meter (N·m). Different industries and regions prefer different units, making conversion a daily necessity for mechanics and engineers worldwide.
Inch-pounds are preferred for small, precision fasteners - electronics screws, bicycle bolts, carburetor fittings, and aerospace hardware. Foot-pounds are standard for automotive lug nuts, cylinder head bolts, and structural fasteners. The practical crossover point is around 200 in·lb (16.7 ft·lb). Using the wrong unit or scale can lead to catastrophic over-torquing.
Torque wrenches should be calibrated annually or after being dropped. A wrench that reads 5% high effectively over-torques every fastener, which can be disastrous on aluminum or composite parts. When converting between units, always double-check your math - a factor-of-12 error (confusing in·lb for ft·lb) is one of the most common mechanical mistakes.
Multiply the inch-pound value by 0.112985. For example, 50 in·lb × 0.112985 = 5.649 N·m.
Both measure torque. One foot-pound equals 12 inch-pounds. Inch-pounds are used for smaller fasteners requiring less torque, while foot-pounds suit larger bolts.
Proper torque ensures the clamping force holds components securely without deforming or breaking them. Under-torque risks loosening; over-torque risks stripping, cracking, or bolt fatigue.
Not accurately. Foot-pound wrenches lack resolution at the low end. For specs under 200 in·lb, use an inch-pound-rated wrench for proper accuracy.
Most automotive spark plugs require 12-20 N·m (roughly 106-177 in·lb or 9-15 ft·lb), depending on thread size and material. Always follow the manufacturer spec.
Yes, in·lb and lb·in refer to the same unit. The terms are interchangeable.