Calculate gallons of paint or stain for your fence. Enter fence length, height, and coverage rate to estimate materials for both sides of the fence.
Staining or painting a fence protects the wood from weathering, UV damage, and rot, dramatically extending its lifespan. However, fences have much more actual surface area than you might expect because of the gaps between pickets, the back side of each board, and the posts and rails. A 100-foot privacy fence at 6 feet tall has approximately 1,200 sq ft of paintable surface — and that's just one side.
This fence paint and stain calculator estimates the total gallons you need based on your fence dimensions, the number of sides you're finishing, and your coverage rate. It accounts for the typically lower coverage rates of exterior stains and paints on rough-sawn wood, which absorbs more product than smooth surfaces.
Whether you have a classic picket fence, a board-on-board privacy fence, or split rail with wire, this tool helps you budget materials accurately and avoid multiple trips to the store.
Tracking this metric throughout the project lifecycle helps project managers identify potential issues early and maintain quality standards from foundation to final inspection.
Fence surfaces are rough and porous, so they absorb significantly more paint or stain per square foot than smooth interior walls. Coverage rates on fence wood can be as low as 150–250 sq ft per gallon for stain and 200–300 sq ft per gallon for paint. Accurate estimation prevents costly shortages mid-project.
Fence Area = Length (ft) × Height (ft) × Sides Gallons = (Fence Area ÷ Coverage per Gallon) × Number of Coats
Result: 14.40 gallons
A 150 ft fence at 6 ft tall with both sides = 150 × 6 × 2 = 1,800 sq ft. At 250 sq ft/gal for stain and 2 coats: 1,800 ÷ 250 × 2 = 14.4 gallons. Purchase 15 gallons (three 5-gallon buckets).
Start with the length and height of your fence to get one-side area. If finishing both sides, double the area. For picket-style fences, multiply by the wood-to-gap ratio. Then divide by the coverage rate and multiply by the number of coats.
Privacy fences (board-on-board) have continuous wood surfaces and are calculated at full area. Picket fences have gaps that reduce the paintable area. Split-rail fences require calculating the surface area of each cylindrical rail rather than a flat surface.
Paint provides a uniform, opaque color that hides wood grain and defects. It's more protective against UV but can peel and requires more prep for reapplication. Stain penetrates the wood, showcases the grain, and is easier to maintain over time because it fades rather than peels.
Clean the fence thoroughly before applying any finish. Use a pump sprayer for speed on large fences, followed by back-brushing to work the product into the wood. Work in manageable sections and maintain a wet edge to avoid lap marks. Apply in temperatures between 50°F and 85°F.
Fence stain typically covers 150–300 sq ft per gallon on rough wood. Semi-transparent stains cover more area (200–300 sq ft) while solid stains cover less (150–250 sq ft) because they deposit more pigment on the surface.
Stain penetrates the wood grain, is easier to reapply, and gives a natural look. Paint sits on the surface, provides more opaque coverage, but can peel over time. Stain is generally recommended for new wood fences; paint works well for previously painted fences.
Staining both sides provides the best protection against moisture absorption and warping. If budget is limited, prioritize the weather-facing side. Some HOAs and local codes require both sides to be finished.
Most fence stains need reapplication every 2–5 years depending on climate, wood type, and stain quality. If water no longer beads on the wood surface, it's time to re-stain.
Yes, a pump sprayer or airless sprayer is the most efficient way to stain a fence. Always back-brush after spraying to work the stain into the wood grain for even absorption and avoid drips.
New rough-sawn wood usually does not need sanding. Smooth-planed wood benefits from light sanding with 80–120 grit to open the pores for better stain absorption. Weathered fences should be pressure-washed rather than sanded.
For picket fences with gaps, reduce the total fence area by the gap percentage. If pickets have 1.5" gaps between 3.5" wide pickets, the gap is about 30%, so multiply the gross area by 0.70 for effective paintable surface.
Oil-based stains penetrate deeper and are more durable in harsh climates. Water-based stains dry faster, have less odor, and clean up with water. Both types work well; choose based on your local climate and personal preference.